5" Gas Vent

The Adapter is used to connect your single wall stove pipe to the twin wall system. Distance to combustible materials: 50mm. Gas Vent lengths and fittings are available with the outer casing fabricated from galvanised steel. The flue liner is aluminium...

The Adapter is used to connect your single wall stove pipe to the twin wall system. Distance to combustible materials: 50mm. Gas Vent lengths and fittings are available with the outer casing fabricated from galvanised steel. The flue liner is aluminium...

Adjustable pipe is available in 125 - 422mm size to ensure that an exact required vent length can be obtained. Distance to combustible materials: 50mm. Adjustable length provides flexibility in the height or length of a vent run and allow for adjustment...

Made from galvanised steel, wall support is designed to provide internal lateral bracing support off a wall or structure. Distance to combustible materials: 50mm. In addition to structural support, the Gas Vent system be secured with guy bracket at...

The Gas Vent Base Support unit is designed to give structural support for an external installation.    Distance to combustible materials (in mm): 50

Elbows can be used to form variable angles and are usually used in pairs or singly to create an offset. Available in 30° and 45° degrees angle option. Distance to combustible materials: 50mm. Gas Vent lengths and fittings are available with the...

Elbows can be used to form variable angles and are usually used in pairs or singly to create an offset. Available in 30° and 45° degrees angle option. Distance to combustible materials: 50mm. Gas Vent lengths and fittings are available with the...

Where the vent passes through a floor or ceiling without support, a Firestop Spacer must be used on both sides of the penetration to provide a barrier to fire and maintain a minimum 50mm (2") air gap clearance to combustible materials. If the Gas Vent...

This is a fitting for connecting a Gas Vent to a flue liner. The flue liner then sits in the 60mm deep socket. Distance to combustible materials: 50mm. Designed to be secured into the top of a stainless steel flexible flue liner at the point where the...

The Gas Vent Guy Wire Bracket is a specific locking band which is used to connect guy wires (not included) from the pipe to the roof when the pipe extends 1.5 mtrs above the roof .    Distance to combustible materials (in mm): 50

Fixed straight pipes are available in three lengths: 1000mm, 500mm and 330mm. Distance to combustible materials: 50mm. Vent pipe lengths and fittings must be installed with the male coupler upwards and female coupler downwards, fitting over the male...

Fixed straight pipes are available in three lengths: 1000mm, 500mm and 330mm. Distance to combustible materials: 50mm. Vent pipe lengths and fittings must be installed with the male coupler upwards and female coupler downwards, fitting over the male...

Fixed straight pipes are available in three lengths: 1000mm, 500mm and 330mm. Distance to combustible materials: 50mm. Vent pipe lengths and fittings must be installed with the male coupler upwards and female coupler downwards, fitting over the male...

The Gas Vent Rafter Support is designed to be used between rafters to give lateral support to twin-wall flue where it exits the roof.   Distance to combustible materials (in mm): 50

An aluminium terminal/cap allows rapid exhaust of combustion products. Gas Vent lengths and fittings are available with the outer casing fabricated from galvanised steel. The flue liner is aluminium. Vertical seams are rolled and securely locked. The...

Aluminium Storm Collar should be fitted to the vent immediately above the Flashing. The Collars are a tight fit to the vent and should be sealed with the silicone sealant. Gas Vent lengths and fittings are available with the outer casing fabricated from...

If the Gas Vent is required to be supported where it penetrates the floor/ceiling Support Plates should be applied. These square heavy gauge galvanised plates must be fixed through the corner holes on top of the floor joist or slab through which the...

Tees may be used at the base of the vent configuration so as to provide access for inspection or cleaning. Available in 90° and 135° degrees angle option. Distance to combustible materials: 50mm. Gas Vent lengths and fittings are available with...

Tees may be used at the base of the vent configuration so as to provide access for inspection or cleaning. Available in 90° and 135° degrees angle option. Distance to combustible materials: 50mm. Gas Vent lengths and fittings are available with...

Lower end of this all aluminium component connects to standard product, upper end fits over fibre cement flue liner. Also used to connect to flexible flue liner. Distance to combustible materials: 50mm. Gas Vent lengths and fittings are available with...